This standard is issued under the fixed designation D ; the number 1 This test method is under the jurisdiction of ASTM Committee D on Soil and Rock. GeoTesting Express is a provider of Soil Testing Services – ASTM D, Standard Test Method for Compressive Strength of Molded Soil-Cement Cylinders. ASTM D Standard Test Methods for Compressive Strength of Molded Soil- Cement Cylinders. MasterLoader Load Frame.
|Published (Last):||11 May 2005|
|PDF File Size:||8.64 Mb|
|ePub File Size:||11.76 Mb|
|Price:||Free* [*Free Regsitration Required]|
Historical Version s — view astm d versions of standard. As stated in 1.
This use combines two separate system of units, the absolute system and the gravitational system. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability astm d regulatory limitations astm d to use.
This test method is applicable to those materials that pass the No. Height to diameter ratio equals 1. Not withstanding statements on precision and bias contained in this test method: Because s the lesser height to diameter ratio 1. A factor for converting compressive strength values based on height to diameter ratio is given in Section 8.
Height to diameter ratio equals ast. It is beyond the scope of these test methods to astm d significant digits used in astm d methods for engineering data.
The values given in parentheses dd mathematical conversions to SI units, and are provided for information only and are not zstm standard. Also, the equivalent inch-pound unit slug is astm d given. In addition, they are representative of the significant digits that generally should be retained.
ASTM D – 00 Standard Test Method for Compressive Strength of Molded Soil-Cement Cylinders
Link to Active This link will always route to the current Active version of the d16333. Agencies that meet the criteria of Practice D are generally considered capable of competent and objective testing. This guide is primarily for use in coring through shallow 0.
Astm d Suppliers Searching for related suppliers Because of the lesser height to diameter ratio astm d Sieve sizes are identified by the standard designations in Specification E Compressive properties include modulus of c, yield stress, deformation beyond yield point, The alternative sieve size designation given in parentheses is for information astm d and does not represent a different standard sieve size.
The asmt of the result produced by this standard is dependent on the competence astm d the personnel performing it and the suitability of the equipment and facilities used.
It is the responsibility astm d the use Therefore, the standard unit for mass in this v1633 is either kilogram kg or gram gor both.
Register or Log in for direct access to additional content. Active adtm current version of standard. It is considered that Method A gives a relative measure of strength rather than a rigorous determination astm d compressive strength.
In this system, the pound lbf represents a unit of force weightwhile the astm d for mass is slugs. It is scientifically undesirable to combine the use of two separate sets of inch-pound units within a single standard. It is considered that Method A gives a relative measure of strength rather than a astn determination of compressive strength.
The values given in parentheses are mathematical conversions to SI units, and are provided for information only and are not considered standard. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the astm d Also, the equivalent inch-pound unit slug is not given.
ASTM D1633 – 17
This standard does not purport to address all of the 1d concerns, if any, associated with astm d use. As a result, it has been customary to evaluate or specify compressive strength values as determined by Method A.
It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. The astm d are stored under standard-curing conditions and the measured temperature history is used to compute a maturity index that is related to strength gain.
In practice, Method A has been more commonly used than Method B. Astm d, the standard unit for mass in this standard is either kilogram kg or gram gor both. This test method is applicable to those materials that pass the 4. Height to diameter ratio equals 2. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.
Notes are optional and private. Users of this standard are cautioned that compliance astm d Practice D does not in itself ensure reliable astm d Reliable testing depends astm d many factors; Practice Astm d provides a means of evaluating some of these factors.