View and Download Canon DRC service manual online. DRC Scanner pdf manual download. Also for: Dr free pdf instructions. Find the office and computer equipment manual you need at ManualsOnline. Canon DRC Scanner User Manual. Page 1. Page 2. Chapter 5. Other Functions. Setting in the User Mode. You can select the mode of operation (user mode) for the scanner from those listed below. ○ Operation.
|Published (Last):||3 September 2004|
|PDF File Size:||5.85 Mb|
|ePub File Size:||9.51 Mb|
|Price:||Free* [*Free Regsitration Required]|
Popular Tags error reset paper jam line clean c01 tray calibration install driver black line scan feed tray image stop scanning memory not found. Page 43 50 mm, the double feed may not be detected. Operation panel 5 buttons; Display LED: Contact your sales maual.
There are no Recommended Downloads available.
20 Most Recent Canon DRC Path-Through Scanner Questions & Answers – Fixya
Page 95 Screw Screw Gear unit Fig. Page 70 In the center, within 26mm of either side Note: Doing so might damage the scanner.
IP cover Screw Upper delivery cover assembly Fig. Slide the roller clamp lever to the right, and push it into the hole in the retard rollers. G Operation panel buzzer setting U Do not sound buzzer during key operation. After that, the pick-up motor and feed motor are started simultaneously to feed the document. Remove the document left in the eject tray. Install the projections in the msnual holes and insert the arm into the hooks until it clicks.
If you turn tray upside down, you will notice screws, remove them carefully.
Canon DR-9080C Service Manual
Page Chapter 7 Daily Cleaning Use a clean, soft cloth to wipe the scanning glasses. Click the [Counter] tab.
Chapter 5 Other Functions Setting in the User Mode You can select the mode of operation user mode for the scanner from those listed below. Page 71 5 years of use or 6 million sheets scanned, whichever product comes first. Page Place the inserted tip into the hole on the right side of cankn machine.
Page Note 2: Press here for open the imprinter cover. Turn the personal computer OFF. Insert the snap band attached to the cable assembly of the IP carriage into the hole located at the center of the main body upper frame. Setting a sheet of paper for the imprinter in the feed path and pressing this button allows you to check the ink discharge.
Canon Scanner DRC User Guide |
Installation Procedure User’s manual. Chapter 2 Preparation Before Cano This chapter describes the procedure from scanner connection through to turning ON the power. It is possible to change the level of detection accuracy with the user mode.
Gear Screw Dd guide Rack Fig. When the document is large Maual or LDR etc. Turn OFF the power to the scanner and the computer before changing the connections, and then turn ON the power and let the computer recognize the scanner again. Page Insert maual snap band attached to the cable assembly of the IP carriage into the hole located at the center of the main body upper frame.
After Replacing Parts If the pick-up sensor turns ON and the paper is correctly fed when the document tray reaches the top, everything is OK. Endorser cover and imprinter cover are open. Check the operation of the pick-up sensor. Page Chapter 7 Daily Cleaning Select the scanner that you are using, and click on the [Properties] button.
Instruct scanning to start from the application.
However, Canon Electronics Inc. Page Chapter 7 Daily Cleaning This chapter describes daily cleaning of the scanner. Preparing 9080v Document Tray Extension Pull out the document tray extension to accommodate the size of the document to be scanned. U Detect staples in the Count Only mode.
Page 42 Turns document run into the registration roller so that Document this way the skew is corrected. Document Guide Lift the document tray assemblyrelease the connectorand detach the document tray assembly and document tray extension Document tray assembly Connector Document tray extension Fig.
Screw Belt Main motor assembly Fig. Press the [Count Only] key on vr operation panel of the scanner. Left Coverand then detach the front side while lifting it upward. I Be sure that the hook is completely latched and the roller cover is not loose. Endorser cover and upper unit are open.